Ad-weighing FG-150KBM Manuel d'utilisateur

FFGG SSeerriieess DDiiggiittaall PPllaattffoorrmm SSccaalleess FG-60KAL / FG-150KAL FG-30KAM / FG-60KAM / FG-150KAM FG-

8 5. BASIC OPERATION 5-1. Turning the power ON and OFF 1. Press the ON/OFF switch to turn the power ON. All the display symbols are displayed a

9 6. Remove the object from the weighing pan. ? The RE-ZERO switch will zero the scale if the weight is within ±2% of the weighing capacity (kg)

10 6. COUNTING MODE Determines a unit weight (the weight of one piece) from sample pieces, and calculates how many pieces on the weighing pan using t

11 7. COMPARATOR The results of the comparison are indicated by HI, OK or LO on the display. The formula to compare is as follows: LO < Lower li

12 8. CALIBRATION This function adjusts the scale for accurate weighing. Calibrate the scale in the following cases. ? When the scale is first used.

13 6. Place the calibration weight on the pan with the same value as displayed, and wait until the STABLE indicator turns on. 7. Press the MODE s

14 9. FUNCTIONS The scale has Function settings to expand your applications. The parameters set in the Function settings are maintained even if the p

15 9-2. Function list Item Description f 1- 0 Auto power-off disabled ? f 1- 1 Auto power-off enabled for battery use only Auto power-off func

16 10. OPTIONS The following options are available for the FG series: ? OP-23 (FG-23) RS-232C serial interface ? OP-24 (FG-24) RS-232C serial inte

17 AX-KO1786-200 DIN 7P D-Sub 9S 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 9 10-2. OP-23 RS-232C serial interface This interface allows FG series to b

This manual and Marks All safety messages are identified by the following, “WARNING” or “CAUTION”, of ANSI Z535.4 (American National Standard Ins

18 Pin connections Data format S T , + 0 0 0 0 0 . 0 0 _ k g CR LF Header Data Unit Terminator ? There ar

19 Data output mode ? Stream mode Function setting “F5-0” The scale outputs the current display data. The data-update rate is approximately 10 time

20 Reply to the command When the “F8-0” is selected, the scale reacts to the received command as follows. ? For the “Q” command, the scale will send t

21 11. MAINTENANCE 11-1. Notes on maintenance ? Do not disassemble the scale. Contact your local A&D dealer if your scale needs service or repai

22 12. SPECIFICATIONS 12-1. Specifications MODEL FG-30KAM FG-30KBM FG-60KAM FG-60KBM FG-150KAM FG-150KBM FG-60KAL FG-150KAL Weight capacity (kg)

23 12-2. Dimensions FG-60KAL FG-150KAL FG-30KAM FG-60KAM FG-150KAM FG-30KBM FG-60KBM FG-150KBM 530 390 289

24 GRAVITY ACCELERATION MAP Values of gravity at various locations Amsterdam 9.813 m/s2 Manila 9.784 m/s2 Athens 9.807 m/s2 Melbourne

25 World map

26 MEMO

27 MEMO

1 Contents 1. INTRODUCTION ...2 2. UNPACKING ...

28 MEMO

3-23-14 Higashi-Ikebukuro, Toshima-ku, Tokyo 170-0013 JAPAN Telephone: [81] (3) 5391-6132 Fax: [81] (3) 5391-6148 A&D

2 1. INTRODUCTION This manual describes how this scale works and how to get the most out of it in terms of performance. FG series platform scales ha

3 3. NAMES AND FUNCTIONS Metric models Weighing unit LCD display STABLE indicator NET indicator ZERO

4 U.S.A. models Indicators STABLE ? Indicates when the reading is stable. NET ? Indicates when NET weight is displayed. (Tare f

5 ? The RE-ZERO , ZERO and TARE switches work when the weight value is stable. ? The RE-ZERO and ZERO switch

6 Screws 4. SETTING UP 4-1. Attaching a display pod to the base (FG-KAL and FG-KAM) 1. First, remove the 4 screws from the bottom of the display col

7 Cautions for installing the scale Consider the following conditions to get the most out of your scale. ? Install the scale where the temperature an